LV7600W

• Overlay: Overlays component signals
• Parade: Displays component signals side by side
• Blanking Interval: H and V blanking periods can be masked.
• Line Select: Displays the selected line
• Variable Gain:
  Gain x1 ×0.2 to ×2.0
  Gain x5 ×1.0 to ×10.0
  Gain x10 ×2.0 to ×10.0

• Overlay: Overlays component signals
• Parade: Displays component signals side by side
• Blanking Interval: H and V blanking periods can be masked.
• Line Select: Displays the selected line
• Variable Gain:
  Gain x1 ×0.2 to ×2.0
  Gain x5 ×1.0 to ×10.0
  Gain x10 ×2.0 to ×10.0

• Overlay: Overlays component signals
• Parade: Displays component signals side by side
• Blanking Interval: H and V blanking periods can be masked.
• Line Select: Displays the selected line
• Variable Gain:
  Gain x1 ×0.2 to ×2.0
  Gain x5 ×1.0 to ×10.0
  Gain x10 ×2.0 to ×10.0

• Compatible SDI Systems Can be displayed for SD, HD, 3G-A, and 3G-B-DL

• Gain: ×1, ×5, IQ-MAG
• Scale:
  Type AUTO, ITU-R BT.601, ITU-R BT.709, DCI, ITU-R BT.2020
  Color Bar Saturation 75 %, 100 %
  IQ Axis Show or hide
• Vector Marker Display

• Function: Converts an SDI signal into Y, R, G, B, and composite values, and then displays the five peak levels.
• Error Level: Based on the gamut error, composite gamut error, and luminance error thresholds

• Histogram Display: Displays the Y, R, G and B histograms

• Display Standard: CIE1931 (xy display), CIE1976 (u'v’ display)
• Display Type: Chromaticity diagram display, color temperature display
• Display Mode:
  Chromaticity Diagram Display
  Luminance display, color display
• Color Temperature Display Luminance display:
  Colorimetry ITU-R BT.601 (525), ITU-R BT.601 (625), BT.709, DCI, ITU-R
  BT.2020

• Level Mapping: Maps the black level to 0 (8bit), SDI code value (when receiving 10 bit RGB) 1024 to 255 (8 bit)
• Display Sizes: Reduced, actual size, ×2 (4K not supported), full frame (4K not supported)
• Quality Adjustment and Color Selection:
  Brightness, contrast, RGB gain, RGB bias, chroma gain,
  monochrome display (RGB gain, RGB bias, chroma gain not valid)

• Error Indication: Displays markers in the gamut error and level error areas

• Function: SCTE-104 message monitoring
• Supported: Standard SMPTE 2010, ANSI/SCTE 104

• Function: Video levels are displayed numerically.
• f Stop Display (not supported on the SER23):
  Displays f Stop values relative to a reference point
  Set in reference to an object with an 18% reflectance
  f Stop gamma correction
• HDR Display (SER23)

• Function: CEA-608, CEA-708 closed caption, Teletext, OP47 subtitle superimposed on SDI signal can be decoded and displayed.

• V-Chip Display

Input Signal: SDI embedded audio
Digital audio I/O connector (SER03)
Analog audio input (SER03) SFP IP Audio (SER05/SER06)

Format: L-PCM, Dolby-E (SER04), Dolby Digital (SER04),Dolby Digital Plus (SER04)

• Function: Records detected errors, events—such as the instrument
  switching between input signals, and timestamps.
• Log Capacity: Up to 1000 events
• Data Output Overwrite mode, Stop after 1,000 events

• Display Format: Displays serial data sequence or displays each color
  component separately
• Line Select: Displays the selected line
• Sample Select: Displays from the selected sample
• Jump Feature: Jumps to an EAV or SAV
• Data Output: Text output to USB memory

• Function: Displays the phase difference between a reference signal and
  an SDI signal numerically and graphically
• Reference Signal: SDI / External sync signal, PTP (SER05/SER06) (*1)
  RTP, External sync signal (BB), FPT (SER06) *1 Complies only with SMPTE ST 2110

• Signal Detection
• Displays the video signal format
• Frequency Deviation Display (not displayed for IP signals)
• Equivalent Cable Length Display (not displayed for IP signals)
• Error Count Display
• Video Error Detection

• SR Live Metadeta analysis display

• Screen capture: A screen capture function to capture the display screen as still image data and a frame capture function to capture 16 frames of data are equipped.
• Frame capture: A frame Capture function to capture 16 frames of the SDI signals is equipped. There are two methods; one is to import them manually and another is to take them automatically when an error occurs.
  * Only one frame is captured when an error occurs.

• Function: Search for data captured by the frame capture function, error search, and export to CSV are possible.

• Excellent operability: The LV5600 adopts a 7-inch full HD panel with a touch panel function.

• Controlled remotely from a Web browser on a PC over an Ethernet connection, and used to perform automatic measurements using TELNET or FTP.

• All operations are possible just by connecting the mouse.

• SDI input 4 BNC connectors
• SDI output 4 BNC connectors (main unit standard equipment)
• Re-clocked Output signal
• The re-clocked output of input SDI signal is available on the respective SDI output terminal.

• Through settings and selection settings
• Through and selection settings in Display Assignment

• Through and selection settings in Display Assignment
• No delay when setting through and selection settings

• The status display has an error detection function of CRC and embedded audio. It also has an event log, data dump, phase difference measurement functions, and can analyze SDI signals.

• The eye pattern waveform, jitter waveform of SDI signal, and the measurement result of each parameter can be displayed.
• Only BNC input 1 supports eye pattern display.

• Simultaneous display of Alignment and Timing

• Lissajous, Status and Surround Display

• Function: Loudness chart display, numeric display, log, level meter display, peak value display
• Supported: Standard ITU-R BS.1770, ARIB TR-B32, EBU R128, ATSC A/85
• Measurement: Channel Simultaneous measurement of two audio sources

• 16ch level meter, Lissajous, surround and status can be displayed by adding LV5600-SER03.

• Measures the time difference between the SDI signal and digital audio signal with a Leader TSG that supports lip syncing. Displays the results numerically and graphically.
• *TSG patterns not made by Leader may be supportable by specifying the video signal setting and audio signal setting.

• Decoding display of Dolby E, Dolby Digital, Dolby Digital Plus becomes possible by adding
  LV5600-SER 04 to LV5600-SER 03 option.

• IP Packet Status Display: The apparatus displays information, including source addresses, destination addresses, and protocols for the IP packets. Display traffic of 10G/25G Ethernet graphically.

• Packet Jitter Measurement: The apparatus measures the arrival intervals of IP stream packets and graphically display temporary fluctuations.
• CSV file copy of Graph data

• PTP Packet Status Display: The apparatus graphically displays PTP time information and network delay information.
• CSV file copy of Graph data

• Video timing relative to PTP
• Audio timing relative to PTP
• Ancillary timing relative to PTP
• Graph display of PTP and each phase

• Video timing with respect to PTP

• Measures the time difference between arriving packets between two IP ports

• SFP transceiver module (IP1 port / OP2 port)
• Display each information

• Displays the MAC and IP of PACKET HEADER

• Displays UDP and RTP of PACKET HEADER

• Recorded in the event log when an IP error occurs

• Possible to monitor up to four channels simultaneously

• You can measure simultaneously by combining four IP and SDI

Requires LV5600 - SER32

• IP Format Ready: Test pattern signal streams conforming to IP format (SMPTE ST 2110-20/30/40) can be generated
• Network Synchronization: Video and audio test signals can be generated in synchronization with SMPTE ST2059 PTP (Precision Time Protocol)
• Packet Error: Packet errors can be added to the test signals (Only ST2110) (Only PORT 1 is supported)
• Packet Jitter: Packet jitter can be added to the test signals (Only ST2110) (Only PORT 1 is supported)

• The measured values of CINST, VRX, or FPT are displayed when the transmission type of SMPTE ST2110-21 is Narrow, Narrow Linear, or Wide. CMAX indicates the value when the packets being sent are full. VRX indicates the value of the virtual receive buffer

• HDR zone display: The luminance distribution of the HDR area can be easily confirmed by coloring the SDR area with monochrome, and the HDR with a color according to the brightness.
• HDR point measurement: The crosshairs can be freely moved. Up to 3 points can be measured simultaneously
• Approved standard
  ITU-R BT. 2100 (HLG, PQ), S-Log 3, C-Log, Log-C
  It corresponds to all except SD input of SDI.

• HDR waveform display
• HDR point measurement:
  The crosshairs can be freely moved.
  Up to 3 points can be measured simultaneously
• Approved standard
  ITU-R BT. 2100 (HLG, PQ), S-Log 3, C-Log, Log-C
  It corresponds to all except SD input of SDI.

• Output pattern: 100% color bar, 75% color bar, HD multiformat color bar *1, 4K multiformat color bar *1, color raster, gamma, cross hatch, 10 step, limit lamp, check field, lip sync pattern(LV5600-SER03 is required), HDR color bar (LV5600-SER23 is required) *1
• Scrolling *2
  Direction: Eight directions (up, down, left, right, and their combinations)
  Speed: Range and Unit Per frame (field) 4 to 124 dots, in 4 dot steps
• Moving Box *2 : ON / OFF
  Colors: WHITE / YELLOW / CYAN / GREEN / MAGENTA / RED / BLUE / BLACK
  Speed: 1 to 3
• Embedded Audio
  *1 It cannot be set in horizontal 4096 and 2048 pixel format.
  *2 Either scrolling, or moving box can be turned on.

• This is a focus detection function realizing a new algorithm based on nonlinear super resolution technology.
• Sensitivity can be selected from 5 levels according to the video scene.

• Focus assist function in the dark

• Various items such as video signal waveforms display, vector display waveforms, and images of input signals can be laid out in any position with your user’s preferred size. Multiple input signals up to 4 inputs can be displayed simultaneously, or one input signal can be displayed on multiple screens.

• Swapping vector and audio

• 1 SDI input signals of 1 to 4 input terminals can be allocated to A to D display channels.

• For example, displaying the signal input to SDI input 1 as component video waveform can be displayed on display channel A and the composite video waveform can be displayed on display channel B.

• Enhanced layout is an extended function that enables the measurement screens of up to four
  channels to be laid out on a single screen simultaneously in simul mode.

• Serial communication RS-422/485 terminals enable to display camera ID, and tally. Fast switching of tally display by remote terminal is also possible.

• Display 4K Payload ID status such as 12G / 6G / 3G

• 4K status mode
• ※LV5600 and LV7600 are supported

• 4K real image

• 4K Quad Link phase differences between links
• ※LV5600 and LV7600 are supported

• 4K Quad Link phase differences between external reference and the links
• ※LV5600 and LV7600 are supported

• BT.2020/BT.709 compatible vectorscope scale simultaneous display

• Support various formats
• Noise Measurement Frequency Band
• Full Digital Processing
• Measurement Window
• Alarm Function

• This feature simplifies the task of identifying the reproduction errors which can occur when transmitting video content produced in BT.709, DCI-P3 or BT.2020 wide color gamut or when converting content from BT.2020 to narrow color gamut.

Requires LV5600 - SER06

• IP Format Ready: Test pattern signal streams conforming to IP format (SMPTE ST 2110-20/30/40) can be generated.
• Network Synchronization: Video and audio test signals can be generated in synchronization with SMPTE ST2059 PTP (Precision Time Protocol).
• Packet Error: Packet errors can be added to the test signals. (Only ST2110)(Only PORT 1 is supported)
• Packet Jitter: Packet jitter can be added to the test signals. (Only ST2110)(Only PORT 1 is supported)

• Character Generator: It's possible to overlay characters on the signal.

• Compressed (JPEG XS), uncompressed (ST2110), SDI, Simultaneous monitoring
• Simultaneous monitoring enables verification of the image quality affected by compression.

• Possible to compare compressed signals.

Requires LV5600 - SER32

• Possible to JPEG XS Test Signal Generator. ※LV5600-SER32 is required

• Analyzing the header of JPEG XS packets and displaying the contents of VideoSupportBox and ColourSpecificationBox.

• We will compare the format information in SDP, ST2110-40 (Payload ID),and ST 2110-22 (JPEG XS).
• Any differing items will be highlighted.